Treatment measures for four types of liquefied foundation

Published Time:

2018-04-29

Introduction: Liquefied sites tend to have lower macroscopic intensities than non-liquefied sites within the same epicentral distance. Theoretically, seismic shear waves are impeded in liquefied soil layers (fluids cannot transmit shear force), causing a corresponding attenuation of seismic waves reaching the ground surface. From the perspective of building vibration damage, this is beneficial to building earthquake resistance. However, more widespread liquefaction damage shows that liquefaction failure of the foundation soil is more destructive to buildings, so the existence of the so-called "damping" effect of liquefied soil cannot be considered beneficial to building earthquake resistance.

Liquefaction sites should prioritize foundation treatment to densify the soil within the building and a certain surrounding range. Specific methods can be selected from the following based on site and building characteristics.

(1) Vibroflotation: Originating in Germany in the 1930s, vibroflotation has been adopted by many countries. It is particularly effective in improving the liquefaction resistance of saturated silty and fine sands, increasing the relative density (Dr) of sand to 0.80.

Vibroflotation has displacement, densification, and vibratory compaction effects on different types of soil layers. For cohesive soils, it mainly plays a displacement role. For medium to fine sands and silty soils, in addition to displacement, it also has compaction and densification effects. During construction in all the above soils, crushed stone (or gravel, etc.) backfill material must be added to the vibroflotation holes to create dense vibroflotation piles, while the soil between the piles is densified and compacted to varying degrees. At the same time, the backfill material forms a gravel drainage well, which allows the sand layer to be compacted and quickly drains water to dissipate the pore water pressure developed in the sand layer, thus better eliminating soil liquefaction.

The main equipment for vibroflotation is a specially designed vibroflotation device with a high-pressure water jet at the front, which causes rapid liquefaction of the sand around the nozzle. The vibroflotation device sinks into the sand layer using its own weight and vibration force, squeezing the floating sand outwards and compacting it during sinking. Once the vibroflotation device reaches the design depth, the lower nozzle is closed and the upper nozzle is opened, while gravel, cobbles, and crushed stone are backfilled into the hole. Then, the vibroflotation device is gradually raised, compacting the fill material and the surrounding sand layer.
   

(2) Dynamic Compaction: Also known as dynamic consolidation or dynamic compaction, this method repeatedly raises a hammer (generally weighing 10-40 tons) to a certain height and allows it to freely fall (fall distance is generally 10-40 meters), giving the foundation an impact and vibration energy to improve its bearing capacity, reduce its compressibility, and improve its performance. Due to its significant strengthening effect, wide applicability, simple equipment, convenient construction, labor saving, short construction period, material saving, civilized construction, and low construction cost, dynamic compaction has been rapidly promoted nationwide in China since its introduction in the 1970s.

Compaction points are generally arranged in a square grid with a spacing of 5-15 meters. Compaction is performed in 1-8 passes. The spacing of compaction points in the first pass is the largest, and it decreases in subsequent passes. The last pass uses low-energy compaction. The interval between passes depends on the dissipation rate of pore water pressure. After each pass, pore water pressure observation is used to understand the dissipation situation and determine the appropriate spacing and time. If the pore pressure rises close to the self-weight of the soil, compaction should be stopped immediately because the soil layer cannot be compacted further. The consolidation depth of dynamic compaction can reach more than 10 meters. One pass of dynamic compaction can cause a settlement of 15-50 cm in a 5-12 m thick alluvial layer.

Dynamic compaction is convenient, has a wide range of applications, is effective, fast, and low-cost, but it is noisy and is more practical in open areas.

(3) Sheet Pile Encapsulation: Encapsulating the potentially liquefiable sand layer around the building with sheet piles and combining this with the sealing effect of compacted backfill soil can significantly reduce the likelihood of sand liquefaction in the foundation.

(4) Backfilling and Compacting Soil and Increasing the Weight of Non-Liquefiable Cover Soil: When the thickness of liquefiable soil at the ground surface or below the foundation is 3-5 meters, backfilling and compaction can be adopted, which is relatively economical and practical. When complete replacement is difficult, it can be verified whether the compacted fill thickness can make the effective stress on the top surface of the saturated sand layer greater than the critical stress that may cause liquefaction. If the compacted fill weight is sufficient, then complete replacement may not be necessary.

The above measures for treating liquefied foundations all eliminate liquefaction by densifying the soil and accelerating drainage. Some foundation treatment methods cannot eliminate liquefaction, such as rigid pile composite foundations (CFG piles).